Skip to main content

DLSOLAR Off-Grid Solar

Solar power for a village borehole is sized from the water duty, not the pump: convert daily litres into hydraulic energy (rho x g x Q x H), divide by wire-to-water efficiency and local peak sun hours, then store energy as elevated water in a tank. Battery-less design removes the system’s most expensive, shortest-lived component.

Start With the Water Duty, Not the Panel

Every borehole project starts with one number: how many litres per day the community actually needs. A practical baseline for drinking and cooking is 20 litres per person per day; village designs usually allow 30-50 litres per person per day once a school, a clinic, a small herd of livestock, and public standpipes are included. Multiply by population and add the seasonal peak — a dry-season village with no alternative source draws harder than an average week.

Second, record the total dynamic head (TDH): static water level, plus drawdown while pumping, plus the vertical rise to the tank, plus friction losses in the riser and delivery pipe. A pump that is perfectly sized for the water duty will still under-deliver if the TDH estimate ignores 15 metres of drawdown or a long rising main. If the borehole yield is unknown, run a step-drawdown test before buying anything: pumping faster than the aquifer refills damages the set and empties the well.

Convert Water Duty Into Hydraulic Energy

Water power is physics, not guesswork. The hydraulic energy to lift a daily volume Q (in cubic metres) through a total head H (in metres) is:

Ehyd = 1000 × 9.81 × Q × H / 3,600,000  (kWh per day)

Then divide by the wire-to-water efficiency of the complete set — motor, pump end, and controller — which for small submersible sets typically lands between 0.45 and 0.55. Worked example: 200 people at 40 litres per person per day gives 8 m³/day; at 40 m TDH that is 0.87 kWh of hydraulic energy and about 1.74 kWh of electrical input per day.

The array follows directly: array size = Eelec / (peak sun hours × derating factor). Use the worst-month peak sun hours for the site, not the annual average, and derate around 0.85 for temperature, dust, and wiring losses. For the example above at 4.5 peak sun hours, the bare minimum is 0.45 kWp; applying a 25 percent duty margin for cloudy days and ageing gives 0.57 kWp. Choose a pump whose best-efficiency point sits near the actual duty — an oversized pump cycling against a closed valve wastes every watt the array produces.

Why Battery-Less Design Wins for Village Water

A battery-less system is a PV array, a controller with maximum power point tracking (or a DC pump with tracking built in), the pump set, and a storage tank. The pump runs whenever the sun is strong enough and pushes water uphill; the tank stores that energy as elevated water. There is no electrochemical battery to over-discharge, overheat, get stolen, or need replacing on a truck that visits twice a year.

Reserve batteries for the few loads that truly cannot wait: a chlorine dosing pump for treated supply, a telemetry unit reporting borehole levels, or a site where no elevated tank is possible. Those loads need a small dedicated battery and charge controller, not a traction-sized bank driving the pump.

Size the Storage Tank as the System’s Battery

In a battery-less design the tank does the work a battery bank would do, so it is sized for autonomy, not for the peak hour. Two days of daily demand is the common target for community drinking water; extend to three days where the rainy season is long and no alternative source exists. Elevation gives free pressure: every 10 metres of tank height delivers roughly 1 bar at the tap, which usually removes the need for a booster pump at the distribution point.

Population Water demand (L/day) TDH (m) Hydraulic energy (kWh/day) Electrical input (kWh/day) Minimum PV array (kWp) Tank, 2-day autonomy (m³)
100 4,000 25 0.27 0.55 0.18 8
200 8,000 40 0.87 1.74 0.57 16
400 16,000 50 2.18 4.36 1.42 32
800 32,000 60 5.23 10.46 3.42 64

Table assumptions: 40 litres per person per day, wire-to-water efficiency 0.50, worst-month 4.5 peak sun hours, 0.85 derating, and a 25 percent duty margin already included in the array column. Round the array up to the nearest practical module block once the real site tilt and horizon shading are known — the off-grid solar calculator lets you re-run these numbers with your own location and head, and the sizing reference covers derating factors in detail.

Protect the Set in the Field

Most pump failures on remote sites are protection failures, not pump failures. A submersible set running dry will destroy its motor within minutes, so fit dry-run protection — a water-level probe in the borehole or a flow switch in the delivery line — wired into the controller lockout. Where the aquifer carries silt or sand, add a strainer above the pump intake and plan periodic surging; abrasive wear is the slow, invisible killer of borehole sets.

The rest is mechanical common sense: a non-return valve to stop the riser draining back through the pump every night, a lockable controller enclosure shaded from direct sun, and a rising main clipped at intervals so its weight does not hang on the pump. Keep the array walkway clear of livestock. Terminology for the components in this article is covered in the off-grid solar glossary.

FAQ

How many solar panels does a village borehole pump need?

Calculate it from the water duty: daily litres converted to hydraulic energy, divided by system efficiency and worst-month peak sun hours. For the 200-person example above the minimum is about 0.57 kWp — typically two to four standard modules — the correct answer is always your own head and daily volume, never a fixed panel count.

Can a solar borehole pump run directly on solar without batteries?

Yes, and for village water it is the preferred arrangement. The pump runs on array power during sunny hours and the elevated tank stores the output; the only battery on site should be the small one serving telemetry or dosing electronics.

What happens during long cloudy periods?

The tank draws down toward empty. Two to three days of autonomy covers normal weather variation; for multi-day storms the operational answer is a temporary demand reduction or a tanker refill, not an endlessly bigger battery.

How deep can a solar borehole pump lift water?

Submersible sets handle deep static levels, but every extra metre of head costs array area. Beyond roughly 100 metres of TDH, verify that the pump stage count matches the duty point and re-check the array sizing — deep lifts can double the kWh per cubic metre compared with the shallow example in this article.

What maintenance does the system need?

Monthly: check tank level behaviour, controller error codes, and array output on a clear midday. Quarterly: clean modules, inspect cables and the non-return valve, and test dry-run lockout by simulating low water. Annually: measure running current against the commissioning record and inspect the rising main for leaks.

Leave a Reply

Your email address will not be published. Required fields are marked *